Xmtg-2000 Temperature Controller Manual Pdf !new! -

Hold for 3 seconds to save changes and return to the main operational screen. Essential Parameter Codes Matrix Parameter Code Description Factory Default Common Adjustments AL1 Alarm 1 Value

| Parameter | Value / Details | | ----------------------------- | -------------------------------------------------------------------------------------------------------------------------------------------- | | | XMTG-2000 series (e.g., XMTG-2001, XMTG-2002, etc.) | | Display Type | 4-digit LED / LCD | | Display Range | -1999 to 9999 | | Measurement Accuracy | ≤ 1.0% FS ± 1 digit (0.5% FS for some models) | | Input Types | Thermocouple (K, J, E, S, B, T), RTD (Pt100, Cu50) | | Control Mode | PID (Proportional-Integral-Derivative) | | Output Options | Relay (3A @ 220V AC resistive), SSR (0-12V DC), 4-20mA, 1-5V, etc. | | Power Supply | 90-242V AC, 50/60 Hz | | Power Consumption | < 3W | | Panel Cutout Dimension | 45 x 45 mm | | External Dimensions (WxHxD) | 48 x 48 x 110 mm | | Weight | Approximately 0.3 kg | | Operating Temperature | 0 to 50℃ | | Relative Humidity | < 85% RH (non-condensing) |

Safety Warning: Always isolate the primary power supply source before handling any physical terminal block connections.

Verify your specific model's voltage requirement on the side casing sticker before powering it on. Sensor Input (Terminals 8, 9 & 10) xmtg-2000 temperature controller manual pdf

The XMTG-2000 supports multiple sensor types configured via the internal software parameters: 0 to 1300°C E-Type Thermocouple: 0 to 600°C J-Type Thermocouple: 0 to 800°C S-Type Thermocouple: 0 to 1600°C Pt100 RTD: -200 to 600°C Cu50 RTD: -50 to 150°C 2. Wiring Diagram and Terminal Connections

The specific steps for setting up your controller will be detailed in its manual, but the general workflow is standard.

The controller is designed for industrial environments. It operates on a wide range of AC voltages (e.g., 85-242VAC, 50/60Hz) and has low power consumption (typically under 4W). It is rated for ambient temperatures of 0 to 50°C and non-condensing humidity below 85%. Hold for 3 seconds to save changes and

XMTG-2000 TYPICAL WIRING LAYOUT +-----------------------------------+ | 1 2 3 4 5 6 7 8 | | [L] [N] [NO] [C] [NC] [+] [-] [A] | +-----------------------------------+ | 9 10 11 12 13 14 15 16 | | [B] [B] [+] [-] | +-----------------------------------+ Terminal Descriptions

Are you experiencing any specific or performance issues? Share public link

However, if you have just installed a new unit or are trying to troubleshoot an existing one, you know that programming it without the instructions can be a headache. Button combinations aren't always intuitive, and parameter codes can be cryptic. Verify your specific model's voltage requirement on the

: The device features a clear LED digital display that shows both the current temperature (PV) and the target setpoint (SV). The Hero’s Journey: Setup and Operation

Offset value to correct discrepancies between the sensor and real temperature. Input Sensor Type 0 (Type K)

Inspect the sensor wiring for shorts. Verify that sensor type settings match the physical hardware. Faulty sensor or incorrect sensor configuration.

To optimize the controller for your specific thermal system, initiate the auto-tuning (AT) function. The controller will then cycle the heating on and off several times to learn the system's characteristics. Once complete, it will automatically calculate and store optimal PID values, ensuring precise control.